The LE Audio Broadcast Sink in subsys/bluetooth/audio/bap_broadcast_sink.c copies subgroup metadata from a received Basic Audio Announcement (BASE) into the static Broadcast Audio Scan Service parameter structure mod_src_param without any bounds check. In base_subgroup_meta_cb() the destination element was selected as mod_src_param.subgroups[mod_src_param.num_subgroups] with no test against ARRAY_SIZE(mod_src_param.subgroups) (sized by CONFIG_BT_BAP_BASS_MAX_SUBGROUPS, default 1), and the metadata was copied with memcpy() using the raw on-air length returned by bt_bap_base_get_subgroup_codec_meta() into a metadata array sized by CONFIG_BT_AUDIO_CODEC_CFG_MAX_METADATA_SIZE (default 4). The BASE validator bt_bap_base_get_base_from_ad() only checks structural consistency and permits up to ~24 subgroups and metadata LTVs of ~240 octets. The defect is reached from the periodic advertising receive callback: pa_recv() → bt_data_parse() → pa_decode_base() → update_recv_state_base() → bt_bap_base_foreach_subgroup() → base_subgroup_meta_cb(). Every broadcast sink registers a scan-delegator receive state at creation (bt_bap_broadcast_sink_create() calls broadcast_sink_add_src()), and CONFIG_BT_BAP_BROADCAST_SINK depends on CONFIG_BT_BAP_SCAN_DELEGATOR, so the path is active in every broadcast-sink build once the device is periodic-advertising-synced. An attacker in radio range who operates a broadcast source the device syncs to — or who impersonates the advertiser address and SID of one already in use, periodic advertising data being unauthenticated — can change the BASE at will; each new BASE is re-parsed. A crafted BASE therefore writes attacker-chosen bytes past the end of a fixed static object in .bss: up to roughly 236 bytes for an oversized metadata LTV, plus whole struct bt_bap_bass_subgroup records for each subgroup beyond CONFIG_BT_BAP_BASS_MAX_SUBGROUPS. This is memory corruption of adjacent Bluetooth-audio state reachable with no pairing, bonding or GATT connection, with a potential for remote code execution in the Bluetooth RX thread; in addition, the unvalidated metadata_len is forwarded to bt_bap_scan_delegator_mod_src(), which neither clamps it nor rejects it, leading to a further copy into the receive state and to out-of-bounds memory being disclosed in the BASS receive-state notification sent to a connected Broadcast Assistant. The fix rejects a BASE carrying more subgroups than the receive state can hold (discarding the update entirely) and omits metadata that does not fit rather than copying it, and additionally honours the previously-ignored error return of the subgroup decode pass.

The user-mode verification handler for the device_deinit() system call, z_vrfy_device_deinit() in kernel/device.c, validated its dev argument with K_SYSCALL_OBJ_INIT(dev, K_OBJ_ANY). k_object_validate() short-circuits its type comparison when the requested type is K_OBJ_ANY, so the check reduced to "this pointer is the base address of some kernel object the calling thread has been granted" — the object's actual type was never compared, and K_SYSCALL_OBJ_INIT also skips the initialization-state check. The sibling handlers z_vrfy_device_init() and z_vrfy_device_is_ready() already used K_OBJ_DRIVER_ANY and were unaffected. A thread running in user mode can therefore pass any kernel object it holds permission on — most usefully a thread stack object obtained from the k_thread_stack_alloc() syscall or a statically defined K_THREAD_STACK it was granted in order to spawn a child user thread — whose backing memory is writable from user mode. z_impl_device_deinit() then interprets those attacker-written bytes as a struct device: it dereferences the state pointer read out of the object, calls the function pointer read out of ops.deinit, and on success writes through state again. The result is an indirect call to an arbitrary address executed in supervisor mode, plus an arbitrary kernel read and a single-byte kernel write. Exploitation gives a local unprivileged thread full kernel code execution, defeating the CONFIG_USERSPACE isolation boundary entirely; a less precise attempt yields a supervisor-mode fault and a system crash. The defect is only reachable in builds that enable both CONFIG_USERSPACE and CONFIG_DEVICE_DEINIT_SUPPORT — with de-initialization support disabled, z_impl_device_deinit() returns -ENOTSUP without ever dereferencing the pointer. In v4.2.x and v4.3.x, CONFIG_DEVICE_DEINIT_SUPPORT defaulted to y, so every CONFIG_USERSPACE build of those releases is exposed unless the option was explicitly turned off. From v4.4.0 the option is opt-in (no default, and not selected by any in-tree subsystem), so a v4.4.x build is exposed only if it enables the option explicitly. The v4.2 line is no longer maintained and receives no backport. The fix changes the object check to K_OBJ_DRIVER_ANY, which constrains the argument to the build-generated driver object type range (K_OBJ_DRIVER_FIRST..K_OBJ_DRIVER_LAST) — the real struct device instances placed by the linker — so the state and ops.deinit fields are once again kernel-controlled.

The ITE IT8xxx2 SHI host-command backend (subsys/mgmt/ec_host_cmd/backends/ec_host_cmd_backend_shi_ite.c) copied the 8-byte host-command request header from the SPI Rx FIFO directly into the shared receive buffer data->in_msg and only afterwards checked the protocol version and the derived packet length. The interrupt handler also accepted a chip-select assertion and an Rx-valid-length (RVLI) interrupt in any driver state other than SHI_STATE_DISABLED, so a new header could be parsed while the host-command thread was still processing the previous request out of the very same buffer. The host processor is the SPI controller and drives both chip select and the clock. After sending a well-formed request it can immediately de-assert chip select — which returns the driver to the ready state and re-enables the FIFO — and start a second transaction carrying a header with data_len = 0xFFFF. Those eight bytes are written into in_msg before the oversized length is rejected, so they land in a buffer whose contents verify_rx() in subsys/mgmt/ec_host_cmd/ec_host_cmd_handler.c has already validated. If this lands in the window before the host-command thread executes args.input_buf_size = rx_header->data_len, the framework hands the registered command handler a 65535-byte input length over a 256-byte buffer. The result is an out-of-bounds read of up to roughly 64 KiB beyond the request buffer: command handlers that copy or echo input_buf_size bytes disclose adjacent embedded-controller memory back to the host or overflow the response buffer, and a read past the end of SRAM faults the controller. The same race also allows cmd_id and cmd_ver to be swapped after checksum verification and after handler lookup. Exploitation requires the ability to drive the inter-processor SHI bus (a compromised host OS or physical access to the SPI lines) and winning a timing race, which the SPI controller can retry indefinitely. The fix parses the header into a local struct ec_host_cmd_request_header and copies it into in_msg only after the length has been bounded by sizeof(data->in_msg), and ignores chip-select and RVLI interrupts outside SHI_STATE_READY_TO_RECV/SHI_STATE_RECEIVING. A residual, bounded race remains: an end-of-transaction interrupt still resets the state to ready while the host-command thread owns the buffer, so a valid second request can still overwrite the in-flight request's contents, unlike the NPCX backend which parks in SHI_STATE_CNL_RESP_NOT_RDY while the buffer is in use.

ieee802154_decipher_data_frame() in subsys/net/l2/ieee802154/ieee802154_frame.c computed payload_len = net_pkt_get_len(pkt) - ll_hdr_len - authtag_len without first checking that the received frame is at least ll_hdr_len + authtag_len bytes long. All three variables are uint8_t, so a frame whose payload is shorter than the configured authentication tag makes the subtraction wrap around to a large value (up to 255). The wrapped length is passed unchanged to ieee802154_decrypt_auth() and on to the CCM operation as cipher_pkt.in_len/out_buf_max, with apkt->tag pointing at frame + ll_hdr_len + payload_len. Because the receive buffer is allocated to the exact length of the frame received from the radio driver, the crypto layer then reads several hundred bytes past the end of the packet buffer and writes the same number of decrypted bytes back over it in place. The frame's authentication tag is only verified after this processing has taken place, so no key material, association or prior authentication is needed — a single crafted short frame from any device in radio range is sufficient. Frame validation in ieee802154_validate_frame() does not prevent it: a data frame is accepted with a one-byte payload. The result is an out-of-bounds read and an out-of-bounds write of up to roughly 240 bytes into the adjacent network-buffer pool, corrupting other packets or allocator metadata and typically faulting the target. The out-of-bounds content is not attacker-chosen (it is ciphertext XOR keystream over out-of-bounds memory) and the frame is dropped when tag verification fails, so the primary impact is memory corruption and denial of service rather than information disclosure. Exposure is limited to configurations that enable the experimental CONFIG_NET_L2_IEEE802154_SECURITY option, select a crypto device via CONFIG_NET_L2_IEEE802154_SECURITY_CRYPTO_DEV_NAME, and have established a security session with a level other than IEEE802154_SECURITY_LEVEL_NONE; with security disabled or at level NONE the tag length is zero and no underflow occurs. The fix rejects frames shorter than ll_hdr_len + authtag_len before the subtraction, and adds the matching guard on the transmit side in ieee802154_create_data_frame().

The Bluetooth Mesh On-Demand Private Proxy solicitation handler in subsys/bluetooth/mesh/solicitation.c copies a received Solicitation PDU into a fixed 17-byte stack buffer without bounding the source length. In sol_pdu_decrypt(), out is allocated as NET_BUF_SIMPLE(17) and then filled with net_buf_simple_add_mem(out, in->data, in->len); net_buf_simple_add() guards its tailroom only with __ASSERT_NO_MSG, which is compiled out in production builds, so when in->len > 17 the underlying memcpy writes attacker-controlled bytes past the 17-byte stack buffer. The copy occurs before any decryption or authentication, so no key material is required to trigger it. The oversized length arises because the mesh scan callback in subsys/bluetooth/mesh/adv.c calls net_buf_simple_restore() before dispatching to bt_mesh_sol_recv(), leaving buf->len covering the entire remaining advertising payload rather than just the Solicitation Service Data. After the parser locates the Service Data AD and consumes the Identification Type byte, the remaining buf->len is the 17-octet Network PDU plus any trailing advertising bytes, and prior to this fix there was no maximum-length check (only a minimum). An attacker can therefore append extra AD structures or padding after the Solicitation Service Data to make buf->len exceed 17. bt_mesh_scan_cb() is registered directly as the BLE scan callback, so buf is raw, unauthenticated advertising data received over the air. Any device in radio range can send a non-connectable advertisement carrying a crafted mesh Proxy Solicitation to a node that has CONFIG_BT_MESH_OD_PRIV_PROXY_SRV enabled and is currently eligible to be solicited (GATT proxy disabled, On-Demand Private Proxy enabled), with no pairing, bonding, or provisioning. The result is an attacker-controlled stack overwrite — plausibly leading to remote code execution and at minimum a reliable remote denial of service. The fix trims buf->len to the spec-fixed 17 octets (dropping the PDU if fewer remain) before decryption.

The NXP GAU ADC driver (drivers/adc/adc_mcux_gau_adc.c) validated the caller-supplied sequence->buffer_size, which is expressed in bytes, against the number of active channels, which is a sample count. It then stored that byte count directly in data->results_length and used it in mcux_gau_adc_read_samples() as the number of uint16_t slots available. Because each conversion result occupies sizeof(uint16_t) bytes, a buffer that was accepted as "large enough" could be written with up to twice its size in bytes, so every sample past the buffer's midpoint was written out of bounds. adc_read() and adc_read_async() are Zephyr system calls. The syscall verifier in drivers/adc/adc_handlers.c only confirms that the caller owns buffer_size writable bytes (K_SYSCALL_MEMORY_WRITE); deciding whether that size is sufficient for the requested channels and extra_samplings is delegated entirely to the driver. On a build with CONFIG_USERSPACE=y, a user-mode thread that has been granted the ADC device object could therefore submit a deliberately half-sized buffer and cause the driver's work-queue handler — which runs in supervisor mode, outside the caller's MPU restrictions — to write ADC conversion results past the end of that buffer, at an address and for a length of the caller's choosing. The overrun is bounded by the requested sequence: with sequence->options->extra_samplings set, the sampling loop walks the buffer pointer forward across every sampling, so the total overrun can reach the full size of the supplied buffer (kilobytes for a large extra_samplings). The written words are 16-bit ADC conversion results, so the content is only partially attacker-influenced (via the selected analog input, gain and resolution), but the destination and length are fully controlled — sufficient for kernel memory corruption, a crash, or a userspace-to-kernel privilege escalation. Builds without CONFIG_USERSPACE, or on SoCs other than NXP RW61x with the GAU ADC node enabled, are not exposed to the privilege boundary; there the same defect only causes a silent overflow when the application itself passes an undersized buffer. The fix replaces the ad-hoc check with the shared adc_sequence_validate_buffer() helper (validating against num_channels * sizeof(uint16_t)), stores buffer_size / sizeof(uint16_t) in results_length, and corrects the loop bound to a post-decrement so exactly the available number of slots may be written.

The system-call verifier for i3c_do_ccc() in drivers/i3c/i3c_handlers.c validated the outer struct i3c_ccc_payload, the broadcast ccc.data buffer and the targets.payloads[] array, but did not validate the per-target data buffers those array elements point at. Each struct i3c_ccc_target_payload carries its own data pointer and data_len, and neither was passed through K_SYSCALL_MEMORY() before the payload was handed to z_impl_i3c_do_ccc() and on to the controller driver. The verifier also operated on the caller's live structure rather than a snapshot, so validated fields could be changed by a second user thread between the check and the driver's use — unlike the sibling z_vrfy_i3c_transfer(), which has always copied its message array first. The defect is only present in CONFIG_USERSPACE builds, where drivers/i3c/i3c_handlers.c is compiled. An unprivileged user-mode thread that has been granted access to the I3C controller device object — the ordinary way an application lets a user thread talk to I3C peripherals — can issue a direct CCC whose target payload data pointer names an arbitrary kernel address. Controller drivers dereference that pointer directly (for example drivers/i3c/i3c_mcux.c, drivers/i3c/i3c_cdns.c, drivers/i3c/i3c_stm32.c, drivers/i3c/i3c_npcx.c), using rnw to decide direction. A read CCC therefore causes the kernel-mode driver to write bus-received bytes into an attacker-chosen kernel address for an attacker-chosen length, and a write CCC transmits kernel memory out onto the I3C bus. The result is an out-of-bounds kernel write plus a kernel memory disclosure, i.e. escalation from a user-mode thread to supervisor privilege, defeating the isolation CONFIG_USERSPACE is meant to provide. The fix introduces copy_ccc_and_do(), which snapshots the payload, copies the target array into kernel memory with k_usermode_alloc_from_copy() (bounding num_targets to fewer than 32), validates each per-target buffer with K_SYSCALL_MEMORY() according to rnw, and copies the driver-written num_xfer and err fields back to the caller.

The MCUmgr SMP-over-console transport decodes a base64 frame, reads a 16-bit packet length from it, verifies a CRC and then unconditionally strips the trailing CRC with rx_ctxt->nb->len -= 2U; in mcumgr_serial_process_frag() (subsys/mgmt/mcumgr/transport/src/serial_util.c). mcumgr_serial_extract_len() accepted any declared length, including 0 and 1, and a packet declaring length 0 passes the checksum test for free because crc16_itu_t() over zero bytes returns the zero seed. Since net_buf::len is a uint16_t, the subtraction underflows and the buffer is handed to SMP claiming roughly 65 KB of payload while its data area is only CONFIG_MCUMGR_TRANSPORT_NETBUF_SIZE bytes (default 384). The trigger is a single unauthenticated 7-byte line on the management console — the 0x06 0x09 packet marker followed by the base64 group AAA= and a newline — delivered to any transport built on this helper: CONFIG_MCUMGR_TRANSPORT_UART (smp_uart.c) or CONFIG_MCUMGR_TRANSPORT_SHELL (smp_shell.c), both of which select MCUMGR_TRANSPORT_SERIAL_HAS_SMP_OVER_CONSOLE. No prior session state, fragmentation or credentials are required to trigger the underflow, and the malformed frame is mishandled before any command handler or command-level access control runs. The attacker only needs write access to that console, which on many boards is a USB CDC-ACM port rather than a bare UART header. With the inflated length, smp_process_request_packet() in subsys/mgmt/mcumgr/smp/src/smp.c loses its bound: cbor_nb_reader_init() gives the CBOR decoder a ~65 KB window into a 384-byte buffer, and each request header's nh_len is checked only against the inflated length. On its own the 7-byte frame re-parses whatever stale bytes the reused pool buffer still holds, typically a replay of the previously received request followed by a parse error, without leaving the buffer. Because the transport is unauthenticated, though, the attacker also controls the frames sent before the trigger, and can stage buffer contents so that a request succeeds with an nh_len larger than the buffer; net_buf_pull(), guarded only by __ASSERT_NO_MSG, then moves the parse cursor out of bounds and the loop reads further headers and CBOR from adjacent memory. The consequence is an out-of-bounds read that can fault the MCUmgr thread (denial of service); memory disclosure is also possible, since the default-enabled os echo handler (CONFIG_MCUMGR_GRP_OS_ECHO) decodes its string inside that window and copies it into its response. There is no integrity gain beyond what the unauthenticated transport already permits. The fix rejects any declared packet length of two bytes or fewer in mcumgr_serial_extract_len(), so the CRC-strip subtraction can no longer underflow. The identical pattern remains in the test-only loopback transport subsys/mgmt/mcumgr/transport/src/smp_dummy.c (CONFIG_MCUMGR_TRANSPORT_DUMMY), which has no external input path and therefore carries no practical exposure.

parse_write_op() in subsys/net/lib/lwm2m/lwm2m_message_handling.c handles inbound CoAP WRITE/CREATE requests that carry a Block1 option. For the first block of a transfer it called init_block_ctx() and then immediately stored the peer-selected block size with block_ctx->ctx.block_size = block_size before inspecting the return code. init_block_ctx() sets the caller's pointer to NULL and returns -ENOMEM when no entry of the static block1_contexts[] pool is free or timed out, so that store dereferences a NULL pointer. The pool holds CONFIG_LWM2M_NUM_BLOCK1_CONTEXT entries (default 3) and an entry is only reclaimed once its transfer completes, fails, or ages past 30 seconds. A peer that reaches the client's LwM2M socket can therefore start three block-wise writes on three distinct object paths with the CoAP More bit set and leave them incomplete, then send the first block of a fourth write on a new path to reach the unguarded dereference. Reachability is gated only by the connected UDP socket's source-address filter unless CONFIG_LWM2M_DTLS_SUPPORT is enabled — which has no default — so in a NoSec deployment an on-path or address-spoofing attacker needs no credentials; the same sequence is also reachable from a bootstrap or lower-trust server, and can be hit accidentally by a legitimate server running four concurrent block transfers. The write targets a fixed low address with a value between 0 and 7, so the consequence is a fatal memory fault (BusFault or corrupted low memory leading to a fault) rather than a usable memory-corruption primitive: the device crashes or resets. Confidentiality and integrity are not affected. The fix moves the store below the guard and validates the context pointer itself instead of the return code, so the context is only touched once it is known to be valid.

The CoAP link-format helper match_path_uri() in subsys/net/lib/coap/coap_link_format.c compares a registered resource path against the URI carried in a Uri-Query href= option. That URI is not NUL terminated, but the inner character loop advanced its index k once per path character without ever testing it against the option length len. When a registered path segment is longer than the supplied URI and the URI is a prefix of it, the loop reads uri[len] and beyond, past the end of the option value. The path is reached from coap_well_known_core_get_len() and coap_well_known_core_get() via match_queries_resource(), i.e. by any unauthenticated GET /.well-known/core?href=/<prefix> request to a device that serves /.well-known/core (for the CoAP server subsystem, CONFIG_COAP_SERVER_WELL_KNOWN_CORE, default y) and has at least one resource that declares struct coap_core_metadata attributes. The over-read does not reach the receive buffer. The well-known-core builders parse the query into a stack-local struct coap_option, whose value is a fixed array (value[12], or CONFIG_COAP_EXTENDED_OPTIONS_LEN_VALUE bytes) that the option bytes are copied into, so uri points into that copy. Reading past len therefore reads the unused, uninitialized tail of the array and, when the option fills it, the bytes just past it in the same stack frame. (In the ZoAP library of v1.8.0 to v1.9.x the option value was instead a pointer into the received packet, and the over-read ran past the option inside the packet buffer.) The impact is bounded. The number of bytes read past the end is limited by the length of the resource path segment, and each additional byte is only read if it happens to equal the next path character, so in practice the over-read is one byte. It also cannot influence the response: returning a match requires the final compared index to be len - 1 or len, both in bounds, so out-of-bounds bytes only ever steer the loop to the next candidate resource. The consequence is undefined behaviour, not information disclosure and not a matching error. The fix adds a k >= len guard at the top of the inner loop, so every uri[k] dereference is within the option value while still allowing a trailing * wildcard to match a longer path.

ieee802154_send() in subsys/net/l2/ieee802154/ieee802154.c copies the outgoing packet into a single fixed 125-byte transmit buffer (tx_frame_buf_pool, sized IEEE802154_MTU). In builds with CONFIG_NET_L2_IEEE802154_FRAGMENT enabled (the default whenever CONFIG_NET_6LO is set), the branch taken when 6LoWPAN fragmentation is not required performed an unchecked net_buf_add_mem(frame_buf, pkt_buf->data, pkt_buf->len). The only guard was __ASSERT_NO_MSG() inside net_buf_simple_add(), which is compiled out without CONFIG_ASSERT, so an oversized packet silently overran the frame buffer. The defect is not reachable from the radio: for NET_AF_INET6 packets ieee802154_6lo_encode_pkt() compares the whole packet length against IEEE802154_MTU and takes the fragmentation path when it does not fit, so every buffer copied on the unfragmented branch is within bounds. It is reachable through NET_AF_PACKET sockets bound to an 802.15.4 interface: for NET_SOCK_RAW the 6LoWPAN block is skipped entirely and for NET_SOCK_DGRAM it returns early on the address-family test, leaving no length validation anywhere on the transmit path (net_context_sendto() and net_if_tx() apply none, and pkt_buffer_length() does not clamp the allocation for this L2). An application — or, in a CONFIG_USERSPACE build, an unprivileged application thread using the zsock_socket()/zsock_sendto() syscalls — can therefore drive a supervisor-mode out-of-bounds write of chosen bytes past the 125-byte pool buffer. With the default CONFIG_NET_BUF_FIXED_DATA_SIZE of 128 bytes the overrun is bounded to roughly ll_hdr_len + 3 bytes; with CONFIG_NET_BUF_VARIABLE_DATA_SIZE a single storage buffer can be as large as CONFIG_NET_PKT_BUF_TX_DATA_POOL_SIZE, making the overrun far larger. The consequence is corruption of memory adjacent to the pool, with a crash or further compromise of kernel state as the practical impact. The fix validates ll_hdr_len + net_pkt_get_len(pkt) + authtag_len against IEEE802154_MTU before any copy and adds a tailroom-checking copy_pkt_to_frame() helper that returns -EMSGSIZE instead of overrunning the buffer. The same change also linearizes the whole net_buf chain into one MAC frame, so packet storage boundaries no longer become frame boundaries on the wire.

The ADC API requires each driver to reject a sampling sequence whose destination buffer is too small: the buffer_size field of struct adc_sequence in include/zephyr/drivers/adc.h documents that "the driver must ensure that samples are not written beyond the limit and it must return an error if the buffer turns out to be not large enough". The ADI MAX32 driver did not honour that contract. start_read() in drivers/adc/adc_max32.c compared buffer_size, a byte count, against a sample count ((1 + extra_samplings) channels), ignoring sizeof(uint16_t), so it accepted a buffer half the required size. The samples are then stored through the uint16_t data->buffer by Wrap_MXC_ADC_GetData(), which writes two bytes per sample and advances the pointer by one uint16_t: in adc_max32_start_channel() for synchronous reads, and in adc_max32_isr() for asynchronous ones. A sequence selecting two channels with a two-byte buffer, for example, passes the check and has its second sample written past the end of the buffer. On a build with CONFIG_USERSPACE, adc_read() and adc_read_async() are system calls. The handler in drivers/adc/adc_handlers.c copies the sequence in from user memory, verifies only that [buffer, buffer + buffer_size) is writable by the calling thread, and rejects a user-supplied options->callback; it deliberately leaves the size arithmetic to the driver. A user-mode thread that has been granted access to a MAX32 ADC device object therefore fully controls channels, buffer, buffer_size and options->extra_samplings, and can make the driver write twice as many bytes as its buffer holds. Because the check scales with extra_samplings, the overrun equals the length of the buffer itself, up to channels * 65536 bytes past its end, since the sample pointer is only rewound on a repeat sampling, never on the extra samplings of a sequence. The resulting stores are performed by the driver in kernel mode (in the system call itself, the ADC context timer, or the ADC interrupt handler for asynchronous reads), where the MPU does not restrict the thread's memory domain, so the write walks linearly out of the user partition and into adjacent memory such as other partitions, kernel data or thread stacks. The impact is kernel-memory corruption of attacker-chosen length at an attacker-chosen offset, a plausible privilege-escalation and denial-of-service primitive from an unprivileged user-mode thread. Builds without CONFIG_USERSPACE are affected only as a caller-side robustness defect, since the application itself supplies the buffer. The fix replaces that check in start_read() with a call to the new shared helper adc_sequence_validate_buffer() in drivers/adc/adc_common.c, passing sizeof(uint16_t) as the sample size. The helper computes active_channels sizeof(uint16_t) (1 + extra_samplings) and returns -ENOMEM before any sampling is started.

The ADC API requires each driver to reject a sampling sequence whose destination buffer is too small: the buffer_size field of struct adc_sequence in include/zephyr/drivers/adc.h documents that "the driver must ensure that samples are not written beyond the limit and it must return an error if the buffer turns out to be not large enough". The NXP MCUX LPADC driver did not honour that contract. mcux_lpadc_start_read() in drivers/adc/adc_mcux_lpadc.c performed no buffer-size check at all before assigning data->buffer = sequence->buffer. Each completed conversion then stores one 16-bit sample per enabled channel per sampling round through an unbounded *data->buffer++: in mcux_lpadc_isr() for interrupt-driven builds, and in mcux_lpadc_dma_callback() for DMA-driven builds on releases that have the DMA path. A sequence selecting two channels with a two-byte buffer, for example, has its second sample written past the end of the buffer. On a build with CONFIG_USERSPACE, adc_read() and adc_read_async() are system calls. The handler in drivers/adc/adc_handlers.c copies the sequence in from user memory, verifies only that [buffer, buffer + buffer_size) is writable by the calling thread, and rejects a user-supplied options->callback; it deliberately leaves the size arithmetic to the driver. A user-mode thread that has been granted access to an LPADC device object therefore fully controls channels, buffer, buffer_size and options->extra_samplings, and can request far more samples than its buffer can hold: up to channels * 65536 samples into a two-byte buffer, since the sample pointer is only rewound on a repeat sampling, never on the extra samplings of a sequence. The resulting stores are performed by the driver in kernel mode (in the ADC interrupt handler or the DMA completion callback), where the MPU does not restrict the thread's memory domain, so the write walks linearly out of the user partition and into adjacent memory such as other partitions, kernel data or thread stacks. The impact is kernel-memory corruption of attacker-chosen length at an attacker-chosen offset, a plausible privilege-escalation and denial-of-service primitive from an unprivileged user-mode thread. Builds without CONFIG_USERSPACE are affected only as a caller-side robustness defect, since the application itself supplies the buffer. The fix calls the new shared helper adc_sequence_validate_buffer() in drivers/adc/adc_common.c from mcux_lpadc_start_read(). The helper computes active_channels sizeof(uint16_t) (1 + extra_samplings) and returns -ENOMEM before any sampling is started.

The userspace verifier z_vrfy_rtio_sqe_copy_in_get_handles() in subsys/rtio/rtio_syscalls.c (subsys/rtio/rtio_handlers.c before v4.3.0) validated the RTIO object handle and the sqes input array, but not the handle out-parameter. On the first loop iteration it executed *handle = sqe, storing the kernel address of the newly acquired submission-queue entry through a pointer taken verbatim from user mode, with no K_SYSCALL_MEMORY_WRITE check in front of it. Any user-mode thread that has been granted a struct rtio kernel object can invoke the syscall with an arbitrary address in handle. That is the ordinary way an unprivileged thread uses the RTIO API, for example via sensor_read_async_mempool() or the async ADC helpers, which call rtio_sqe_copy_in_get_handles() internally. The store happens in supervisor mode before any submission-entry validation, so it fires regardless of whether the SQE contents are subsequently rejected. Only builds with CONFIG_USERSPACE and CONFIG_RTIO are affected; without CONFIG_USERSPACE the verifier is not compiled and the caller is already privileged. The write address is fully attacker-chosen and the written value is a pointer into the caller's own RTIO ring, whose contents the caller controls (the following *sqe = sqes[i] copies an attacker-supplied struct rtio_sqe into that slot). This yields a write-what-where primitive placing a pointer to attacker-controlled data at any kernel address, sufficient to corrupt kernel function pointers, thread structures, or memory-domain partition tables, and thus to escalate from user mode to kernel mode, defeating the isolation boundary CONFIG_USERSPACE is meant to enforce. At minimum it is a reliable kernel memory-corruption and crash primitive. The reporter reproduced the write on qemu_x86: a K_USER thread changed a supervisor global from NULL to a live kernel SQE pointer. The fix adds K_SYSCALL_MEMORY_WRITE(handle, sizeof(*handle)) (guarded by the existing optional-NULL semantics) before the loop, so the destination must lie in the calling thread's writable memory domain or the thread is terminated by K_OOPS. The neighbouring verifier z_vrfy_rtio_cqe_get_mempool_buffer(), which checked its buff/buff_len out-parameters only for read although the implementation writes through them, was hardened separately by bea93400138 ("rtio: syscalls: validate output params as writable"); that residual was materially weaker, since a read check still confines the target to the caller's own memory domain.

The Intel SEDI IPM (inter-processor mailbox) driver in drivers/ipm/ipm_sedi.c handles an inbound message interrupt in ipm_event_dispose(). It read the peer-written doorbell register, extracted the payload length with IPC_HEADER_GET_LENGTH(), and passed that length straight to sedi_ipc_read_msg() to copy the message into struct ipm_sedi_context.incoming_data_buf, without checking it against the buffer size. The doorbell length field is 10 bits wide (IPC_HEADER_LENGTH_MASK is 0x03FF), so it can encode up to 1023 bytes, while incoming_data_buf is IPC_DATA_LEN_MAX (128) bytes. The bounds check in the underlying HAL sedi_ipc_read_msg() is a DBG_CHECK that compiles away unless CONFIG_DEBUG is set, so no check remained in a production image. The doorbell register is written by the peer processor on the other side of the IPC link — for the intel_ish_5_* targets, the host CPU's ISH driver, reached through the device's memory-mapped register window. Host-side software with driver-level or raw BAR access can therefore set a length of up to 1023 and cause the interrupt handler to copy far past the destination buffer. The affected path requires an application to have registered an IPM receive callback via ipm_register_callback(), which is the driver's normal mode of use. The result is an out-of-bounds write of up to 895 bytes into static (.bss) memory, performed in interrupt context. The overflow first clobbers the rest of struct ipm_sedi_context — including the k_sem and k_mutex used by the transmit path, whose wait queues contain self-referential list pointers — and then adjacent static data, giving a kernel data-structure corruption and crash primitive. The overflowing bytes are read from registers following the message window, a portion of which are themselves peer-programmable. The fix rejects any doorbell whose encoded length exceeds IPC_DATA_LEN_MAX, logging it and acknowledging the doorbell so the peer is not left waiting.

The SMBus driver API exposed smbus_smbalert_remove_cb() and smbus_host_notify_remove_cb() as Zephyr syscalls. Their verifiers in drivers/smbus/smbus_handlers.c validated only the dev argument with K_SYSCALL_OBJ(dev, K_OBJ_DRIVER_SMBUS) and forwarded the caller-supplied struct smbus_callback *cb pointer into kernel-mode driver code without any K_SYSCALL_MEMORY_READ/K_SYSCALL_MEMORY_WRITE validation. A companion change in 2023 had already removed the matching smbus_smbalert_set_cb() / smbus_host_notify_set_cb() syscalls for this reason, but the two removal syscalls were left exposed. On a build with CONFIG_USERSPACE=y, CONFIG_SMBUS=y and a driver implementing the callback operations (drivers/smbus/intel_pch_smbus.c with CONFIG_SMBUS_INTEL_PCH_SMBALERT/CONFIG_SMBUS_INTEL_PCH_HOST_NOTIFY, or drivers/smbus/smbus_stm32.c with CONFIG_SMBUS_STM32_SMBALERT), any user-mode thread that has been granted the SMBus device object can invoke these syscalls with an arbitrary pointer. The value reaches smbus_callback_remove() in drivers/smbus/smbus_utils.h, which uses it as a node identity against the kernel's sys_slist_t of registered callbacks. The consequence is that an unprivileged thread can unregister an SMBALERT or Host Notify callback that a supervisor-mode component registered, silently disabling alert handling for the rest of the system; because Zephyr images have fixed symbol addresses and the syscall returns 0 on a hit versus -ENOENT on a miss, the target address is both derivable and searchable. In builds with CONFIG_ASSERT=y the __ASSERT(callback->handler, ...) check additionally dereferences the caller-supplied address in supervisor mode, so a bogus pointer raises a kernel-mode fault and a fatal system error, and the fault/no-fault outcome discloses which addresses are mapped. The fix removes both syscall entry points, demoting the two functions to ordinary static inline calls so that callback list manipulation is available only to supervisor-mode code. There is no impact on builds without CONFIG_USERSPACE, and no impact on configurations that do not enable an SMBus driver with SMBALERT or Host Notify support.

The Time-aware GPIO syscall verification handler z_vrfy_tgpio_pin_read_ts_ec() in drivers/timeaware_gpio/timeaware_gpio_handlers.c validated only the port device object and passed the caller-supplied timestamp and event_count output pointers to the driver without a K_SYSCALL_MEMORY_WRITE() check. The other handlers in the same file (z_vrfy_tgpio_port_get_time(), z_vrfy_tgpio_port_get_cycles_per_second()) already performed that check, so the omission left one syscall unguarded. tgpio_pin_read_ts_ec() is declared __syscall, so with CONFIG_USERSPACE=y an unprivileged user-mode thread that has been granted access to the TGPIO device object can invoke it with arbitrary pointer values. tgpio_intel_read_ts_ec() in drivers/timeaware_gpio/timeaware_gpio_intel.c bounds-checks only the pin index and then unconditionally performs timestamp = ... and event_count = ..., executing two 8-byte stores in supervisor mode at addresses chosen by the user-mode caller. The result is a write-what-where primitive that crosses the userspace/kernel boundary: the target address is fully attacker-chosen and the stored values are the hardware time-capture and event-counter register contents. Corrupting kernel data structures this way can escalate the calling thread to supervisor privilege or crash the system; the device-object permission required is a narrow capability that is not intended to confer any kernel-memory access. The fix adds the two missing K_SYSCALL_MEMORY_WRITE() validations before the driver call. Exposure is narrow in practice. Only builds with CONFIG_USERSPACE=y and CONFIG_TIMEAWARE_GPIO=y compile the affected file, and from v3.6.0 onward the file additionally referenced a relocated header (<zephyr/syscall_handler.h>) and removed Z_SYSCALL_* macros, so such a configuration failed to build until those were repaired after v4.4.0. Downstream trees that locally corrected that breakage, and v3.5.0 builds where it did not exist, are the exposed population.

The experimental USB host stack allocates a per-device configuration-descriptor buffer, udev->cfg_desc, from the dedicated usb_device_heap in usbh_device_set_configuration() (subsys/usb/host/usbh_device.c). On three failure paths — a failed full-length GET_DESCRIPTOR(CONFIGURATION) read, a mismatch between the short and full descriptor reads, and a rejected descriptor in parse_configuration_descriptor() — the buffer was released with k_heap_free() but the pointer was left dangling. The cleanup in usbh_device_free() is guarded only by if (udev->cfg_desc != NULL), so it frees the same block a second time. The path is driven entirely by the attached peripheral: usbh_device_connect() calls usbh_device_init(), which ends in usbh_device_set_configuration(), and on failure usbh_device_connect() calls usbh_device_free(). On v4.4.x this happens during the same enumeration, with no unplug required; on v4.1.0–v4.3.x the second free instead arrives via dev_removed_handler()/dev_connected_handler() in subsys/usb/host/usbh_core.c, so it requires a removal or duplicate-connect event after the failed enumeration — a sequence the attached device fully controls. A malicious or malformed USB device only has to answer the first 9-byte configuration-descriptor request with a well-formed header and then fail any of the three checks, for example by returning a full descriptor whose interface count disagrees with bNumInterfaces, or by answering the second read with different bytes. The result is a double free on usb_device_heap. On builds where lib/heap hardening is active (the current default CONFIG_SYS_HEAP_HARDENING_BASIC), sys_heap_free() detects the already-free chunk and calls k_panic(), giving a deterministic, peripheral-triggered denial of service of the USB host. On builds without that detection — earlier releases, or CONFIG_SYS_HEAP_HARDENING_NONE — the second free manipulates a chunk already on the free list, corrupting the heap's free list so that later allocations can return overlapping or invalid blocks. Exploitation beyond denial of service is bounded by the fact that usb_device_heap is a small dedicated heap (CONFIG_USBH_USB_DEVICE_HEAP, default 1024 bytes) whose only client is this descriptor buffer, and by CONFIG_USB_HOST_STACK being marked experimental and disabled by default. The fix sets udev->cfg_desc = NULL after every k_heap_free(), making the cleanup guard sound.

net_icmpv6_send_error() in subsys/net/ip/icmpv6.c implemented only one of the three RFC 4443 section 2.4 suppression rules (do not answer an ICMPv6 error with an ICMPv6 error). It did not check whether the triggering packet's source address identifies a single node (rule e.6) or whether the packet was sent to a multicast destination (rule e.3, whose only exceptions are Packet Too Big and Parameter Problem Code 2). Of the five call sites, only the port-unreachable path in subsys/net/ip/connection.c carried an equivalent guard of its own; the extension-header, unknown-next-header and fragmentation paths in subsys/net/ip/ipv6.c and subsys/net/ip/ipv6_fragment.c had none. An unauthenticated attacker with access to the same link can exploit this in two ways. Sending a single IPv6 packet to the link-local all-nodes group ff02::1 carrying an unrecognized next-header value, with the source address spoofed to a chosen victim, causes every Zephyr node on the link to emit an ICMPv6 Parameter Problem message to that victim — a reflector with an amplification factor equal to the number of nodes. Alternatively, sending a unicast packet whose source address is a multicast address causes the node to transmit its ICMPv6 error to that multicast address, turning one unicast packet into a link-flooded multicast frame. Packets addressed to ff02::1 are accepted unconditionally by ipv6_input(), and no check rejects a multicast source address, so no special configuration is required. The impact is degraded availability of the shared link and of the reflection victim, together with the ability for the attacker to hide its own address behind the responding nodes. The effect is amplified on constrained mesh links such as 802.15.4/Thread, where link-local multicast is flooded hop by hop. There is no memory-safety consequence: the error packet itself is well formed, it is simply emitted in cases where the protocol forbids it. The fix adds both suppression checks at the single choke point in net_icmpv6_send_error(), before any reply packet is allocated, preserving the RFC-mandated exceptions for NET_ICMPV6_PACKET_TOO_BIG and Parameter Problem Code 2. Note that the IPv4 counterpart net_icmpv4_send_error() in subsys/net/ip/icmpv4.c still checks only for a broadcast destination and retains an equivalent gap for multicast destinations and non-unique sources.

gptp_handle_msg() in subsys/net/l2/ethernet/gptp/gptp.c dereferenced the gPTP header returned by GPTP_HDR() and switched on hdr->message_type without first checking that the received frame carries at least sizeof(struct gptp_hdr) (34) bytes of payload. The header accessor gptp_get_hdr() deliberately never fails for a short buffer — it returns pkt->frags->data and leaves validation to its callers — so a truncated frame produced a header pointer covering memory beyond the received data. The per-message-type checks that follow do not compensate: GPTP_VALID_LEN() reduces to len > 60 once the Ethernet header has been pulled, which is false for every fixed-size gPTP message, so GPTP_CHECK_LEN() never rejects a truncated SYNC, FOLLOWUP, PDELAY_RESP or SIGNALING message. The defect is reached by an unauthenticated peer on the same link sending an Ethernet frame with ethertype 0x88F7 to the PTP multicast address on an interface configured as a gPTP port, with CONFIG_NET_GPTP enabled. Because conformant Ethernet pads frames to 60 bytes, a payload shorter than 34 bytes generally requires a link that can deliver sub-minimum frames — for example the native_sim TAP driver (drivers/ethernet/eth_native_tap.c), which forwards whatever length the host device supplies, or a MAC configured to accept undersized frames. The short packet is retained (net_pkt_ref() into rcvd_sync_ptr, rcvd_follow_up_ptr, rcvd_pdelay_resp_ptr or rcvd_announce_ptr) and later parsed by the media-dependent and media-independent state machines in subsys/net/l2/ethernet/gptp/gptp_md.c and subsys/net/l2/ethernet/gptp/gptp_mi.c, which read tens of further bytes and copy some of them (the announce priority vector, hdr->port_id) into state that is subsequently transmitted. Under the default fixed-size buffer allocator (CONFIG_NET_BUF_FIXED_DATA_SIZE, 128-byte fragments) the accesses stay inside the allocated fragment and disclose stale recycled buffer contents; under the experimental CONFIG_NET_BUF_VARIABLE_DATA_SIZE allocator, where fragments are heap-allocated at the exact frame length, they are genuine out-of-bounds reads. There is no write and no availability impact.

The ITE it82xx2 USB device-controller driver initialized its bus-suspend detection work with k_work_init_delayable(&priv->suspended_work, suspended_handler) inside it82xx2_enable() (the driver's .enable op) in drivers/usb/udc/udc_it82xx2.c. This work item is scheduled essentially continuously while the USB bus is active: the interrupt handler reschedules it on every SOF frame and suspended_handler() reschedules itself, so its timeout node is normally linked in the kernel timeout list / a workqueue pending queue. k_work_init_delayable() (kernel/work.c) unconditionally overwrites the entire k_work_delayable structure, including its timeout and queue linkage, with no busy check. Because it82xx2_disable() does not cancel the work, a normal disable-then-enable cycle re-runs api->enable() (udc_enable() only rejects a redundant enable, not a re-enable after disable) and re-initializes the still-pending work in place, corrupting the kernel timeout/workqueue linked lists and causing a kernel panic. An external USB host — for example a host performing USB DFU detach (dfu-util --detach) or forcing repeated attach/reset/re-enumeration — drives the udc_disable()/udc_enable() transitions and controls suspend/resume timing, so it can arrange for the suspend work to be pending across a re-enable. This yields an unauthenticated denial of service (kernel panic) reachable across the USB boundary from a removable, physically-connected host, with no confidentiality or integrity impact demonstrated. The fix moves the k_work_init_delayable() call into the one-time preinit function so the work is initialized exactly once, eliminating the re-initialization of an in-use item.

The Zephyr SDIO subsystem function sdio_io_rw_extended_helper() in subsys/sd/sdio.c finishes transfers with a byte-I/O loop that uses size = MIN(remaining, func->cis.max_blk_size) as the per-iteration step. The value func->cis.max_blk_size is decoded directly from the SDIO card's CIS FUNCE tuple in sdio_decode_cis() and is not validated. When a card reports a maximum block size of zero, size is always 0, remaining never decreases, and the loop spins forever. The loop is reached from the public SDIO client API used by drivers, including sdio_read_fifo(), sdio_write_fifo(), and the incrementing register read/write helpers, each of which enters the loop while holding the per-card mutex func->card->lock. A card advertising max_blk_size == 0 therefore hangs the calling thread permanently on its first non-block-aligned transfer and never releases the mutex, denying service to the SDIO peripheral (and any subsystem such as Wi-Fi that depends on it) until the device is reset. The malicious value must come from the SDIO card itself, so the defect is exploitable where a removable SDIO/combo card slot lets an attacker insert a crafted or malfunctioning card (a physical attack vector); on boards with a soldered SDIO peripheral it is not attacker-influenceable. There is no memory-safety, confidentiality, or integrity impact — only a permanent availability loss. The fix returns -EIO when func->cis.max_blk_size is zero, before the loop is entered.

net_if_ipv6_calc_reachable_time() in subsys/net/ip/net_if.c derives a randomized ND reachable time from ipv6->base_reachable_time as min_reachable + sys_rand32_get() % (max_reachable - min_reachable), where min_reachable = base/2 and max_reachable = 3*base/2 using integer division. When base_reachable_time is 1, both min_reachable and the modulus collapse so the function returns 0, and net_if_ipv6_set_reachable_time() stores that 0 into ipv6->reachable_time. The base_reachable_time is attacker-controlled: handle_ra_input() in subsys/net/ip/ipv6_nbr.c accepts the Reachable Time field of an incoming Router Advertisement whenever it is nonzero and <= MAX_REACHABLE_TIME, so a single unauthenticated, link-local RA carrying a Reachable Time of 1 drives the computed reachable time to 0. Router Advertisements are unauthenticated by default and require only adjacency to the target link. When a neighbor is subsequently confirmed reachable, net_ipv6_nbr_set_reachable_timer() reads the value and executes NET_ASSERT(time, "Zero reachable timeout!"). On builds with CONFIG_ASSERT enabled this triggers a fatal kernel assertion — a remote denial of service; on builds without assertions the reachable timer is armed with K_MSEC(0) and fires immediately, forcing reachable neighbors into perpetual re-solicitation (STALE), degrading Neighbor Discovery. The impact is limited to availability; there is no memory-safety, confidentiality, or integrity consequence.

The MQTT-SN client keepalive handler process_ping() in subsys/net/lib/mqtt_sn/mqtt_sn.c removes the gateway record after PINGREQ retries are exhausted. It invoked SYS_SLIST_PEEK_HEAD_CONTAINER(&client->gateways, gw, next) but discarded the result. That macro is a pure expression that does not assign to gw, so gw retained its NULL initializer regardless of the list contents. The code then dereferences the NULL gw (gw->gw_id) and passes it to mqtt_sn_gw_destroy(), reaching k_mem_slab_free(&gateways, NULL). With CONFIG_MEM_SLAB_POINTER_VALIDATE enabled this triggers k_panic(); in the default configuration it performs a write through the NULL pointer ((char )mem = slab->free_list;) and corrupts the slab free list. The outcome is a crash/kernel panic or, on targets where address 0 is writable, silent memory-allocator corruption. The vulnerable branch runs whenever the connected MQTT-SN gateway fails to answer keepalive PINGREQs for the configured number of retries. This condition is controlled by the remote peer: a malicious or compromised gateway, or an on-path/adjacent attacker that advertises itself as a gateway and then stops responding (or blackholes the real gateway's PINGRESPs), forces the client into the defect. MQTT-SN runs over UDP and no authentication is required. The impact is a remotely triggerable denial of service (availability) of the affected MQTT-SN client; there is no attacker-controlled data written. The sibling remover process_advertise() uses SYS_SLIST_FOR_EACH_CONTAINER_SAFE and is not affected. The fix assigns the macro's return value to gw.

The Bluetooth Classic (BR/EDR) L2CAP receive handler bt_l2cap_br_recv() in subsys/bluetooth/host/classic/l2cap_br.c dispatched inbound data PDUs based only on the destination channel ID, without checking that the target channel had reached the BT_L2CAP_CONNECTED state. A dynamic channel is assigned its RX CID and added to the connection's channel list while still in BT_L2CAP_CONNECTING (and later BT_L2CAP_CONFIG) — before configuration completes and, for PSMs that require security, before the peer is authenticated (l2cap_br_conn_req()). Because the channel is already findable by bt_l2cap_br_lookup_rx_cid() during this window, a remote peer within radio range can send a data PDU addressed to that CID and have it processed on a not-yet-established channel. The dispatch keys off channel fields (BR_CHAN(chan)->rx.mode, rx.mps) that are only initialized during configuration by l2cap_br_conf(); since channel objects are pooled and bt_l2cap_br_chan_del() does not reset rx.mode or the reassembly buffer _sdu, a reused channel can carry stale state into the CONNECTING window and route the frame into the retransmission/flow-control path (bt_l2cap_br_ret_fc_recv()) with stale parameters and a possibly stale _sdu pointer. The impact is delivery of attacker data to upper-layer protocol handlers on a half-open (and possibly unauthenticated) channel, plus operation on stale or partially initialized channel state on reused channel objects — leading to channel/link teardown (denial of service) and, in the stale-_sdu case, a dangling-pointer condition. The fix adds an explicit BR_CHAN(chan)->state < BT_L2CAP_CONNECTED guard that drops any data received before the channel is fully connected.

net_ipv6_send_ns() in subsys/net/ip/ipv6_nbr.c allocates a transmit net_pkt for a Neighbor Solicitation. When it is called with a data packet pending on an unresolved neighbor and that neighbor's pending_queue is already non-empty (an NS is already outstanding), the function appends the data packet and returns early without ever sending the NS via net_send_data() or releasing it with net_pkt_unref(). The freshly allocated NS net_pkt and its attached TX buffers are held only by a local variable and are leaked permanently, never returning to CONFIG_NET_PKT_TX_COUNT / CONFIG_NET_BUF_TX_COUNT. The leaking branch sits on the normal IPv6 transmit path: net_ipv6_prepare_for_send() (called from net_if.c) invokes net_ipv6_send_ns() for any outbound or forwarded IPv6 packet whose next hop is not yet in the neighbor cache. An on-link (adjacent) attacker can drive it deterministically by sending a burst of request packets (for example ICMPv6 echo requests or UDP datagrams) that all spoof a single non-existent on-link source address: the node generates a reply to each, the first reply queues an NS, and every subsequent reply during the roughly three-second INCOMPLETE resolution window takes the leaking branch and loses one TX packet. Router-configured nodes forwarding attacker traffic toward a non-existent on-link host leak identically. Because the leaked packets are never reclaimed and CONFIG_NET_PKT_TX_COUNT defaults to only 4 (14 for Ethernet), a brief low-rate burst exhausts the TX pool. Once exhausted the node can no longer allocate any transmit packet and cannot send TCP/UDP, ARP/ND, or any reply at all, producing a complete and persistent network denial of service that does not self-heal until reboot. The fix releases the unsent NS packet with net_pkt_unref(pkt) before the early return.

The I3C IBI subsystem in drivers/i3c/i3c_ibi_workq.c hands out statically-allocated work nodes through a free-list i3c_ibi_work_nodes_free implemented as a plain sys_slist_t, which provides no synchronization. The allocation helpers (i3c_ibi_work_enqueue, i3c_ibi_work_enqueue_target_irq, i3c_ibi_work_enqueue_hotjoin, i3c_ibi_work_enqueue_controller_request, i3c_ibi_work_enqueue_cb) called sys_slist_get() directly from ISR context, while the workqueue handler i3c_ibi_work_handler() returned nodes with sys_slist_append() from the workqueue thread, with no lock on either side. Because sys_slist_get() and sys_slist_append() are neither atomic nor interrupt-safe, an IBI interrupt that fires while the workqueue thread is mid-append (or a truly parallel access under CONFIG_SMP) races on the shared list. This corrupts the list linkage: a node may be handed to two consumers, a node may be lost, or the head/tail pointers may be left inconsistent so sys_slist_get() returns a stale or garbage pointer. In the double-hand-out case the subsequent memcpy(ibi_node, ibi_work, sizeof(*ibi_node)) overwrites a node still in flight; a garbage pointer turns the same memcpy into an out-of-bounds write. The race is driven by I3C bus traffic — IBIs, hot-joins, and controller-role requests originate from target devices on the bus, and I3C supports hot-joining devices. An attacker controlling an I3C peripheral on the board's chip-to-chip bus can generate high-frequency interrupts timed to collide with the free operation. Exploitation requires physical access to the bus and winning a narrow timing window; the most realistic impact is a crash or hang (denial of service), with memory corruption possible but hard to control. The fix wraps all free-list sys_slist_get()/sys_slist_append() operations in the new ibi_work_alloc()/ibi_work_free() helpers, each guarded by a k_spinlock (ibi_work_lock), closing the race across ISR and thread contexts.

The LwM2M JSON content formatter's get_string() in subsys/net/lib/lwm2m/lwm2m_rw_json.c copies a parsed JSON string into a caller-supplied buffer and NUL-terminates it. The length guard used if (string_length > buflen), which accepts a string whose length is exactly buflen. After memcpy() fills the whole buffer, buf[string_length] = '\0' then writes one byte past the end of the buffer (CWE-787). The string value and its length are taken directly from the incoming CoAP payload during a LwM2M WRITE: do_write_op_json() parses the payload obtained from coap_packet_get_payload(), and get_string() is invoked from lwm2m_write_handler() (engine_get_string() in subsys/net/lib/lwm2m/lwm2m_message_handling.c) for a LWM2M_RES_TYPE_STRING resource. The destination buf/buflen is either the resource instance's fixed data buffer (res_inst->data_ptr/max_data_len) or the engine validation buffer (msg->ctx->validate_buf). A LwM2M server (the client's DTLS peer) can therefore write a string resource with a value whose length equals the target buffer size and force a one-byte overflow. The overflow is a single out-of-bounds write of the constant byte 0x00 immediately past the resource or validation buffer, corrupting the adjacent byte in memory. It is not an information leak and the written value is fixed, so it is not a direct code-execution primitive, but it can corrupt adjacent state (an adjacent resource value, a length/flag field, or a struct field) and cause data corruption or a crash. Triggering the write is deterministic; the resulting impact depends on memory layout. The fix changes the guard to string_length >= buflen, rejecting the exact-length case and aligning the JSON formatter with the other content formatters (lwm2m_rw_plain_text.c, lwm2m_rw_oma_tlv.c, lwm2m_rw_senml_json.c, lwm2m_rw_cbor.c, lwm2m_rw_senml_cbor.c), which already used the correct boundary check.

The Silicon Labs SiWx917 WiFi driver's transmit callback siwx91x_send() in drivers/wifi/siwx91x/siwx91x_wifi.c frees a network packet it does not own. In the Zephyr TX path the net_pkt is owned by the L2/networking stack; the driver only borrows it to copy the frame bytes into a local net_buf. Before the fix, after transmitting, siwx91x_send() additionally called net_pkt_unref(pkt) on the caller-owned packet, dropping its last reference and returning it to the shared packet pool prematurely. This code path is compiled in by default (CONFIG_WIFI_SILABS_SIWX91X_NET_STACK_NATIVE). The caller, ethernet_send() in subsys/net/l2/ethernet/ethernet.c, keeps using the packet after the driver returns: it reads net_pkt_get_len(pkt), updates TX statistics, and then performs its own net_pkt_unref(pkt). Because the driver already released the packet, these are use-after-free reads followed by a second unref (a double free). When concurrent network activity recycles the freed slab slot between the two unrefs, the trailing unref decrements a different, live packet's reference count and frees it, corrupting the net_pkt pool shared by both the receive and transmit paths. The defect is exercised by ordinary transmission over the native-stack SiWx917 WiFi interface, and an adjacent attacker on the same WiFi network can induce transmissions (for example ARP or ICMP echo replies, or TCP handshakes) to drive the path. The primary observable impact is loss of availability (transmit hangs and crashes from pool corruption), with race-dependent memory corruption of the kernel networking buffer pool. The fix removes the erroneous net_pkt_unref(pkt) from siwx91x_send(); the driver's receive-path unref, which correctly frees a packet the driver itself allocated, is unaffected.

The IEEE 1588 PTP management-message parser in subsys/net/lib/ptp/tlv.c mishandles the PTP_MGMT_TIME management id. In tlv_mgmt_post_recv(), the PTP_MGMT_TIME case casts mgmt_tlv->data to a 10-byte struct ptp_timestamp and reads it (then byte-swaps and writes it back) without first checking that the TLV data field is at least sizeof(struct ptp_timestamp). Every sibling management id in the same switch validates its length first; PTP_MGMT_TIME was the only case lacking that check. The length passed in is the management data size (tlv->length - 2), and the upstream guard in ptp_tlv_post_recv() only requires tlv->length > 2, while msg_tlv_post_recv() validates only that the TLV fits within the received byte count, not a per-id minimum. A peer on the local PTP segment can therefore send a PTP_MSG_MANAGEMENT message carrying a short PTP_MGMT_TIME TLV (data as small as 2 bytes), causing the parser to read and write 8 bytes beyond the validated data. The message type and TLV contents are taken straight off the wire, so the path is reachable by any adjacent attacker when CONFIG_PTP is enabled. The over-read and write-back stay within the struct ptp_msg allocation (mgmt_tlv->data lives in the leading mtu[NET_ETH_MTU] union member, so data + 10 lands at most a few bytes past mtu[], inside the same object), so this is an out-of-bounds read of adjacent in-object memory plus a bounded in-place corruption of the message's parsed timestamp, not past-allocation memory corruption. Impact is limited to minor information exposure of adjacent bytes and corruption of the device's parsed management TIME value; there is no crash on the access and no reachable reference-count corruption. The fix adds if (length < sizeof(struct ptp_timestamp)) { return -EBADMSG; } before the cast, matching the other management-id cases and fully closing the receive-path defect.

The LoRaWAN application-layer clock-synchronization service parses downlinks in clock_sync_package_callback() (subsys/lorawan/services/clock_sync.c). Its command loop only guarantees that the one-byte command id is in bounds; for the CLOCK_SYNC_CMD_APP_TIME (AppTimeAns) command the handler then reads a 4-byte time correction via sys_get_le32() plus a 1-byte token without checking that 5 bytes remain in the receive buffer (len - rx_pos). A short or crafted AppTimeAns therefore reads up to 5 bytes past the end of the decrypted payload. The payload (rx_buf/len) is the decrypted application frame delivered to the registered downlink callback (mcps_indication->Buffer/BufferSize). Reaching the handler requires a frame on the clock-sync port that passes LoRaWAN's MAC integrity check and FRMPayload decryption, so the practical attacker is a malicious or compromised network/application server (the designated sender of AppTimeAns) or a party holding the session keys, rather than an arbitrary radio listener. The over-read is bounded: the backing store is a fixed 255-byte static buffer, so the few stray bytes do not fault, and the read values (time_correction, token) are used only internally and never transmitted, so there is no disclosure to the attacker and no crash. The sole effect is that a stale token matching ctx.req_token can apply a garbage time_correction to the device's own clock offset (ctx.time_offset), a minor integrity impact confined to the victim's time estimate. The fix adds an explicit length check that drops a too-short AppTimeAns. Note the sibling one-byte reads in the periodicity and force-resync handlers remain unguarded with the same negligible impact.

The Zephyr ext2 filesystem driver validates the on-disk block bitmap in ext2_init_fs() (subsys/fs/ext2/ext2_impl.c) by passing fs_blocks = s_blocks_count - s_first_data_block to ext2_bitmap_count_set(). That helper (subsys/fs/ext2/ext2_bitmap.c) treats its argument as a number of bits and reads one bitmap byte per eight bits, but the bitmap buffer (BGROUP_BLOCK_BITMAP) is a single fetched block of only fs->block_size bytes (capacity fs->block_size * 8 bits). s_blocks_count and s_first_data_block are taken verbatim from the superblock and were never bounded against this single-group capacity; ext2_verify_disk_superblock() checks the magic, revision, and block-size shift but not the block count. A crafted ext2 image with an oversized s_blocks_count (up to ~4 billion, against a maximum 4096-byte block / 32768-bit bitmap) makes ext2_bitmap_count_set() scan roughly 512 MB of memory past the bitmap block — a large out-of-bounds read of the static block slab and adjacent memory. The defect is reached during mount: ext2_init_fs() is invoked from ext2_mount() (subsys/fs/ext2/ext2_ops.c), the registered .mount operation. Any path that mounts an attacker-supplied ext2 image (removable media, a disk/flash partition, or a downloaded image) triggers it. The kernel-privileged parser operates on attacker-controlled data, so the bug is exploitable wherever untrusted ext2 media can be mounted. Impact is an out-of-bounds read only: the resulting bit count is compared internally and the mount is rejected, so no attacker-controlled bytes are returned (not a useful information leak). The ~512 MB over-read will almost certainly cross an unmapped or MPU-protected boundary and fault, crashing the system — a denial of service triggered by mounting a single malformed image. The fix rejects any image whose fs_blocks exceeds fs->block_size * 8 before the scan.

The Zephyr virtio driver does not validate the descriptor-chain head id that the virtio device writes into the used ring. In virtio_isr() (drivers/virtio/virtio_common.c), the device-written vq->used->ring[idx].id is used directly as an index into vq->recv_cbs[] and vq->desc[], which are both allocated with exactly vq->num entries. recv_cbs[] holds {cb, opaque} callback entries, and the indexed callback pointer is then invoked as cbe.cb(cbe.opaque, used_len). Because the id is consumed as a 16-bit value with no bound check, a malicious or compromised virtio backend (an untrusted hypervisor, or an untrusted hardware/peer-processor virtio device on a PCI or MMIO transport) can supply an id far beyond vq->num. This causes an out-of-bounds read of a {function pointer, argument} pair from heap memory beyond recv_cbs[], after which the driver calls that attacker-shaped pointer in the guest's interrupt context. No guest privileges or user interaction are required; the backend triggers it by writing the shared used ring and raising the queue interrupt. The result is an arbitrary / attacker-influenced function-pointer call in the Zephyr guest, i.e. a control-flow-hijack primitive that can lead to code execution or, at minimum, a reliable crash. The fix rejects any used-ring id >= vq->num before indexing recv_cbs[]/desc[] or invoking the callback. This affects builds using CONFIG_VIRTIO with the PCI or MMIO transport.

The Zephyr ext2 filesystem driver fails to validate the s_log_block_size field of the on-disk superblock when mounting a filesystem. ext2_verify_disk_superblock() in subsys/fs/ext2/ext2_impl.c checks the magic number, revision, inode size and group counts, but never bounds s_log_block_size. On a successful verify, subsys/fs/ext2/ext2_ops.c computes fs->block_size = 1024 << superblock.s_log_block_size from this attacker-controlled uint32_t, so a crafted value either overflows the shift (undefined behaviour) or yields a block size far larger than CONFIG_EXT2_MAX_BLOCK_SIZE. That block size is then passed to k_mem_slab_init() by ext2_init_blocks_slab() to carve CONFIG_EXT2_MAX_BLOCK_COUNT blocks out of the fixed static buffer __ext2_block_memory_buffer, whose size is CONFIG_EXT2_MAX_BLOCK_COUNT * CONFIG_EXT2_MAX_BLOCK_SIZE. k_mem_slab_init() does not verify that the requested blocks fit the buffer, and the ext2 wrapper discards its return value, so the slab is laid out past the end of the static buffer. The mount immediately reads block-group, bitmap and inode blocks of fs->block_size bytes each into these slab blocks, producing an out-of-bounds write into adjacent static memory on the first block read. The entire path is gated only by data read from the mounted image, making this reachable by any attacker who can present a crafted ext2 image to a device that mounts it (for example a removable SD card or storage medium). Because the ext2 driver runs in kernel mode, supplying image bytes yields a supervisor-mode memory-corruption primitive, with impact ranging from denial of service to potential code execution. The fix rejects s_log_block_size values that overflow the shift (greater than 11) or that produce a block size exceeding CONFIG_EXT2_MAX_BLOCK_SIZE, so the block slab can no longer be initialized larger than its backing buffer.

The virtio PCI driver (drivers/virtio/virtio_pci.c) parses a device's PCI capability list during driver initialization. In virtio_pci_read_cap() the device-supplied capability length byte cap_len (read from PCI config space via pcie_conf_read()) was only checked with assert(tmp.cap_len == cap_struct_size). That assert resolves to __ASSERT_NO_MSG(), gated by CONFIG_ASSERT, which defaults off in production builds, so the value reached the copy logic completely unvalidated. The length then drives a loop that copies extra capability dwords into a fixed-size stack buffer supplied by the caller. A cap_len below the 24-byte base struct virtio_pci_cap underflows the unsigned extra_data_words count to a near-SIZE_MAX value, producing an effectively unbounded stack write; a cap_len above the caller's buffer (up to 255) writes up to roughly 228 bytes of device-controlled data past the buffer. Both are out-of-bounds writes of attacker-controlled content executed in kernel mode during boot-time device probe. The input originates from the virtio device. In the common deployment where Zephyr runs as a guest under a hypervisor, the device backend is the host, which already fully outranks the guest, so the bug yields no privilege escalation. The exploitable case is a virtio device that is untrusted relative to the Zephyr kernel — an untrusted or physical/passthrough virtio PCIe device on a bare-metal system, or a confidential-computing posture where the guest must defend against the host — where a malicious device can corrupt the kernel stack and potentially achieve code execution or a crash. The fix replaces the compiled-out assert with a runtime range check rejecting cap_len outside [sizeof(struct virtio_pci_cap), cap_struct_size] before any arithmetic or copy.

The Hearing Access Service (HAS) GATT server in subsys/bluetooth/audio/has.c installs a connection-callback set unconditionally via BT_CONN_CB_DEFINE, so security_changed() runs for every connection that establishes security even before the application has called bt_has_register(). The service attribute pointers hearing_aid_features_attr, preset_control_point_attr, and active_preset_index_attr remain NULL until bt_has_register() resolves them and sets has.registered. With CONFIG_BT_SETTINGS, settings_set_cb() restores each bonded client's persisted context at boot and unconditionally sets context->flags to BONDED_CLIENT_INIT_FLAGS (non-zero). When a previously bonded peer reconnects and re-establishes security during the startup window before bt_has_register() has been called, security_changed() sees the non-zero flags and schedules notify_work_handler, which calls bt_gatt_is_subscribed() with a still-NULL attribute pointer. That triggers an assertion (__ASSERT(attr, ...) in bt_gatt_is_subscribed()), or a NULL dereference of attr->uuid when assertions are compiled out. The result is a remotely triggerable (Bluetooth, adjacent) crash of the HAS peripheral. Exploitation requires the peer to have previously bonded with the device and to reconnect within the boot-time race window before the application registers the service; a peer that reconnects persistently can prolong the outage. Impact is denial of service only, with no memory corruption or information disclosure. The fix adds an early if (!has.registered) { return; } guard in security_changed(), so no notification work is scheduled until the GATT service is registered and its attribute pointers are valid.

The OCPP 1.6 client in subsys/net/lib/ocpp/ocpp_j.c contains a stack buffer overflow in parse_getconfig_msg(). When handling a GetConfiguration request from the central system, the handler copied the attacker-controlled JSON "key" string into the caller's fixed 50-byte stack buffer (skey[CISTR50], declared in subsys/net/lib/ocpp/ocpp.c) using an unbounded strcpy(). The parsed key value points directly into the receive buffer, so its length is bounded only by the message size (CONFIG_OCPP_RECV_BUFFER_SIZE, default 2048). The GetConfiguration message is delivered over the WebSocket connection that the charge point opens to its configured central system. The reader thread ocpp_wsreader() reads the message into ui->recv_buf and dispatches it to parse_getconfig_msg() via the PDU function table. An attacker who controls the central system endpoint, or a man-in-the-middle on an unencrypted connection, can send a GetConfiguration request whose "key" field exceeds 50 bytes and overflow the reader thread's stack with attacker-chosen bytes. The consequence is a remotely triggerable stack smash on the OCPP reader thread: at minimum a denial of service, and plausibly remote code execution depending on build-time hardening such as stack canaries and MPU configuration. The fix replaces the strcpy() with a bounded strncpy(key, payload.key[0], CISTR50 - 1) followed by explicit NUL termination, matching the bounded copies already used by the sibling handlers.

The userspace syscall verifier z_vrfy_mbox_send() in drivers/mbox/mbox_handlers.c validated the nested msg->data/msg->size fields by reading them directly out of live userspace memory, and then forwarded the original, still-mutable userspace struct mbox_msg * pointer to z_impl_mbox_send() and the underlying driver. Between the access check and the driver's use of msg->data, the validated pointer could be replaced, leaving a time-of-check/time-of-use window. On a system built with CONFIG_USERSPACE, any unprivileged userspace thread may invoke the mbox_send() system call. A second thread sharing the caller's address space can race to overwrite msg->data with a supervisor (kernel) address after the verifier's bounds check has passed but before the driver dereferences it. The driver then reads from the attacker-chosen address in supervisor context (for example memcpy(&data32, msg->data, msg->size) in the NXP mailbox driver, whose bytes are subsequently emitted to the peer mailbox endpoint). The impact is a userspace-to-supervisor access-control bypass: disclosure of kernel memory contents (high confidentiality impact), or, for an invalid/unmapped target address, a faulting kernel read causing denial of service. The fix snapshots the entire struct mbox_msg into a kernel-stack copy with k_usermode_from_copy() and validates and forwards that immutable copy, closing the race.

The OCPP 1.6 client in subsys/net/lib/ocpp/ocpp.c reconstructs a session handle and PDU id from the uid field of a CALLRESULT message. In ocpp_process_server_msg() the code calls atoi(strtok_r(uid, "-", &tmp)) without checking the strtok_r return value. When the server-supplied uid is empty or contains no - delimiter, strtok_r() returns NULL and atoi(NULL) dereferences a NULL pointer, which is undefined behaviour. The uid originates from network data: parse_rpc_msg() in subsys/net/lib/ocpp/ocpp_j.c JSON-parses a frame received from the OCPP central system over TCP/WebSocket and copies the server-controlled string into the local buffer. A malicious or compromised central system, or a man-in-the-middle on a non-TLS ws:// connection, can return a malformed uid to reach the defect. No authentication beyond the existing server connection (or MITM position) is required, and the reconstructed pointer is membership-validated by ocpp_session_is_valid(), so the impact is limited to the NULL dereference rather than arbitrary pointer use. On Zephyr targets that trap access to address 0 (MMU/MPU platforms or CONFIG_NULL_POINTER_EXCEPTION_DETECTION), the dereference faults inside the OCPP reader thread and invokes the fatal handler, producing a remote denial of service of the charge point; on bare targets where address 0 is readable the call returns 0 and is benign, so the impact is availability-only and platform-conditional. The applied fix guards only the first atoi(); the second strtok_r(NULL, "-", &tmp) followed by pdu = atoi(buf) in the same function remains unguarded and the identical NULL dereference is still reachable from the same network input when the uid has a first token but no second --delimited token. A complete fix should validate the second token as well.

The Infineon Airoc Wi-Fi driver's transmit callback airoc_mgmt_send() in drivers/wifi/infineon/airoc_wifi.c allocates a net_buf from the fixed airoc_pool for every outbound packet. When whd_network_send_ethernet_data() returns a synchronous failure, the underlying WHD library does not take ownership of the buffer, but the pre-fix driver returned -EIO without releasing it. Each failed transmit therefore permanently leaks one buffer from the pool. airoc_pool is small and fixed (AIROC_WIFI_TX_PACKET_POOL_COUNT + AIROC_WIFI_RX_PACKET_POOL_COUNT, default 20 buffers) and is shared by WHD's whd_host_buffer_get callback for both transmit and receive. Once enough send failures have leaked the pool dry, airoc_wifi_host_buffer_get() returns WHD_BUFFER_ALLOC_FAIL for all subsequent allocations, so both transmit and the WHD-driven receive path fail and Wi-Fi connectivity is lost until the device is rebooted. The leak occurs only on the transmit error path. A Wi-Fi-adjacent attacker can influence the conditions that cause synchronous send failures (for example by deauthenticating/disassociating the station while the local stack continues to attempt transmits), and ordinary transient failures over the device's lifetime accumulate toward the same state. Reliable on-demand triggering is of high complexity and the impact is availability-only, but the resulting denial of service is permanent and non-recoverable without a reboot. The fix releases the buffer with airoc_wifi_buffer_release() on the failure branch, returning it to the pool. The commit also removes a redundant k_sem_give() in airoc_mgmt_disconnect(); because data->sema_common is a binary semaphore (limit 1) the duplicate give merely saturated at 1 and had no security impact.

The Sierra Wireless HL7800 cellular modem driver (drivers/modem/vendor_standalone/hl7800.c, located at drivers/modem/hl7800.c in v4.4.0 and earlier) parses AT responses with roughly twenty handlers that call net_buf_linearize(value, sizeof(value), *buf, 0, len) into a 128-byte stack buffer and then write value[out_len] = 0. Because net_buf_linearize() (lib/net_buf/buf.c) can return a count equal to its destination-length argument, a field that exactly fills the buffer makes the terminating NUL land one byte past the end, a single-byte out-of-bounds write into adjacent stack memory. The +KCELLMEAS cell-measurement handler on_cmd_atcmdinfo_rssi() is worse: it passed the wire length len as the destination size (net_buf_linearize(value, len, *buf, 0, len)), so a response line longer than 128 bytes overflows the value stack buffer with attacker-influenceable content. The line length comes from net_buf_findcrlf(), which accumulates bytes across the whole net_buf fragment chain and is not bounded to 128, so an over-long line reaches the defect. The data originates from the cellular modem over UART, driven by the network: operator-scan results, +CGCONTRDP IP/DNS info, socket indications, and +KCELLMEAS neighbour-cell reports. An attacker able to shape what the modem emits — a rogue base station, a compromised modem baseband, or a remote peer feeding oversized response framing — can drive a line past 128 bytes. The handlers run in the driver's RX thread in kernel context, so the corruption is kernel-side. The +KCELLMEAS path is a full stack buffer overflow whose worst case is code execution in kernel context and whose floor is a reliable crash; the remaining sites are single-byte NUL out-of-bounds writes. Exploitation requires the modem to emit an over-long AT response line, giving high attack complexity over an adjacent (cellular radio) vector. The fix passes sizeof(dst) - 1 (and correct explicit bounds for the IMSI and +KCELLMEAS sites) so the terminator always stays in bounds.

The NVS backend of the Zephyr settings subsystem (subsys/settings/src/settings_nvs.c) reads stored setting-name entries into fixed 74-byte stack buffers and NUL-terminates them with buf[rc] = '\0', where rc is the return value of nvs_read(). Per its contract, nvs_read() returns the full stored entry length (wlk_ate.len), which can exceed the supplied buffer length — only MIN(len, stored_len) bytes are actually copied, but the return value may be much larger, bounded only by the NVS sector size. Three sites (settings_nvs_cache_match(), settings_nvs_load(), and settings_nvs_save()) used this value directly as the NUL index without clamping, so an oversized stored name entry causes a single \0 byte to be written past the end of the stack buffer at an attacker-influenced offset (CWE-787). The oversized entry cannot arise through the normal settings API, where names are bounded by SETTINGS_MAX_NAME_LEN. It requires an actor able to write the flash that backs the settings partition — a co-resident or untrusted component sharing the flash device, a malicious settings image/restore, or offline/physical flash access (a shared-flash threat model). The malformed entry is parsed when settings_load() runs at boot or subsystem init, or during settings_save(). The out-of-bounds write is a single NUL byte at an offset equal to the crafted entry length (up to the NVS sector size), so the practical impact is a crash or denial of service and limited stack corruption rather than reliable code execution. There is no confidentiality impact, and the path is not reachable from the network through the ordinary settings interface. The fix skips any entry whose nvs_read() length is greater than or equal to the buffer size before performing the NUL store.

The WNC-M14A2A LTE-M modem driver mishandles unsolicited %NOTIFYEV: events in on_cmd_socknotifyev() (drivers/modem/vendor_standalone/wncm14a2a.c). The response line is linearized into a fixed 40-byte stack buffer via net_buf_linearize(), which caps the copy at 39 bytes and returns out_len <= 39. The two quote-delimiter scanning loops, however, were bounded by len — the full CR/LF-delimited frame length returned by net_buf_findcrlf() — rather than by out_len. When a %NOTIFYEV: line longer than 39 bytes contains no " within the linearized region, the loop indices p1/p2 walk past value[39] and read adjacent stack memory until a stray quote byte is found or the index reaches len. The over-read string is then passed to strncmp()/atoi()/LOG_*, and if a quote byte is found out of bounds the subsequent value[p2] = '\0' performs a single-NUL out-of-bounds stack write at an attacker-influenced offset. The %NOTIFYEV: payload carries network-derived content (LTIME network time, SIB1 base-station system information, CSPS/RRCSTATE), so a rogue cellular base station, a malicious or compromised modem module, or RF manipulation that induces an over-long notify line reaches the defect without any application interaction; the handler runs automatically on the unsolicited event in the modem RX thread. The impact is out-of-bounds stack disclosure (into logs and parsing) and stack corruption that can crash the modem RX thread (denial of service). The write offset is only weakly controlled, so memory-safe code execution is not demonstrated. The fix bounds both scanning loops by out_len, keeping all accesses within the linearized buffer.

The Zephyr kernel validates the k_thread_join() and k_thread_abort() system calls (declared __syscall in include/zephyr/kernel.h) through thread_obj_validate() in kernel/thread.c. Its default switch branch is the access-denied path, taken when k_object_validate() returns -EPERM (the calling user thread was never granted access to the target thread object) or -EBADF (the supplied pointer is not a registered kernel object of the right type). That branch invoked K_OOPS(K_SYSCALL_VERIFY_MSG(ret, "access denied")), but K_SYSCALL_VERIFY_MSG treats a true expression as success; the non-zero error code ret therefore read as "verified OK", the kernel oops was never raised, and control fell through to CODE_UNREACHABLE. Because k_thread_join() and k_thread_abort() are system calls, an unprivileged user-mode thread (under CONFIG_USERSPACE) can reach this denial path directly by calling either syscall on a thread object it does not own. Instead of the offending thread being cleanly terminated, execution reaches __builtin_unreachable() while running in supervisor mode inside the syscall handler. On Clang builds CODE_UNREACHABLE emits an illegal-instruction trap, so a user thread can deterministically crash the kernel — a locally triggerable denial of service that escapes the userspace sandbox. On GCC builds the path is undefined behavior: the compiler may drop the return-value handling for thread_obj_validate(), so it can return an undefined bool; if that is false, the caller proceeds into the real k_thread_join()/k_thread_abort() implementation for a thread the user was never authorized to access, an access-control bypass. The fix changes the verification expression to ret == 0, so a denied (non-zero) result now correctly raises K_OOPS and terminates the offending caller.

The HL7800 cellular modem driver's +CGCONTRDP: response handler on_cmd_atcmdinfo_ipaddr() in drivers/modem/vendor_standalone/hl7800.c parses the PDP-context dynamic parameters (local address, subnet mask, gateway, and DNS servers) that the cellular network assigns to the device. The response is linearized into a 256-byte stack buffer, after which each address field length is computed from comma/. delimiter positions in the network-supplied data and used directly as the length argument to strncpy() into the fixed 64-byte stack buffer temp_addr_str (and the 16-byte iface_ctx.dns_v4_string). Because the field length is derived from attacker-controlled delimiter positions and was not bounded against the destination buffer, a single field can be far larger than 64 bytes. A malicious or impersonated cellular network (for example a rogue base station) can return a crafted +CGCONTRDP response with an overlong address field, causing strncpy() to write past temp_addr_str on the modem worker thread's stack, plus an out-of-bounds NUL write at temp_addr_str[addr_len]. No device-side privileges or user interaction are required: the device itself issues the AT+CGCONTRDP=1 query during normal network attach and parses whatever the network returns. The overflow corrupts adjacent stack memory in supervisor context, yielding at minimum a remotely triggerable crash and potentially control-flow hijacking on targets without stack protection. The fix bounds every field length against its destination buffer (temp_addr_str and dns_v4_string) before each copy, rejecting overlong fields.

Zephyr's Precision Time Protocol receive handler ptp_msg_post_recv() in subsys/net/lib/ptp/msg.c takes the 4-bit message type straight off the wire via ptp_msg_type() (msg->header.type_major_sdo_id & 0xF, range 0-15) and uses it to index the msg_size[] table. That table only defines entries up to PTP_MSG_MANAGEMENT (0xD), giving it ARRAY_SIZE == 14. Before the fix there was no upper-bound check, so the undefined types 0xE and 0xF indexed one or two int slots past the end of the array — an out-of-bounds read of adjacent read-only data. The out-of-bounds value is then reused as a length: it gates msg_size[type] > cnt, and when it is small or negative it makes cnt - msg_size[type] a large positive budget passed to msg_tlv_post_recv(), whose TLV loop then walks the message suffix past the received bytes, performing further out-of-bounds reads and in-place byte-swap writes on memory beyond the message slab. The defect is reached directly from the network: ptp_port_event_gen() in subsys/net/lib/ptp/port.c reads a PTP frame with ptp_transport_recv() and calls ptp_msg_post_recv() with the attacker-chosen type. PTP uses UDP multicast or raw Ethernet (0x88F7) and is unauthenticated, so any host on the same link can trigger the indexing on a CONFIG_PTP-enabled node with no preconditions. The reliably reproducible impact is a denial of service (fault/crash); a limited memory-corruption path exists but depends on the build-specific value adjacent to msg_size[], which the attacker cannot tune. The fix rejects type >= ARRAY_SIZE(msg_size) with -EBADMSG before any indexing.

The flash_copy() system call is verified by z_vrfy_flash_copy() in drivers/flash/flash_util.c. On builds with CONFIG_USERSPACE enabled, this handler is the kernel-side trust boundary for a user-mode caller. Prior to the fix it validated only the output buffer (K_SYSCALL_MEMORY_WRITE) and passed the two struct device * arguments, src_dev and dst_dev, directly into the implementation without any object validation — unlike every sibling flash syscall, which guards its device pointer with K_SYSCALL_DRIVER_FLASH. A user-mode thread fully controls the values of src_dev/dst_dev and the contents of its own address space. The implementation z_impl_flash_copy() dereferences these pointers and calls through their driver-API function tables (e.g. api->get_parameters(dst_dev), flash_read(src_dev, ...), flash_write(dst_dev, ...)). By supplying a pointer to a forged struct device whose api table contains attacker-chosen function pointers, an unprivileged thread can cause the kernel to call arbitrary code in supervisor mode; passing any arbitrary or invalid address otherwise yields a kernel crash or out-of-bounds read. The result is a local privilege escalation out of the userspace sandbox (with kernel denial-of-service and information disclosure as lesser outcomes). The fix adds K_SYSCALL_DRIVER_FLASH(src_dev, read) and K_SYSCALL_DRIVER_FLASH(dst_dev, write) to z_vrfy_flash_copy(), which verify each device is a registered flash-driver kernel object the calling thread is permitted to use before any dereference, closing the path completely.

The IPv6 neighbor-discovery code in subsys/net/ip/ipv6_nbr.c processes the 6LoWPAN Context Option (6CO, RFC 6775) carried inside ICMPv6 Router Advertisements. In handle_ra_6co() the 8-bit context_len field is taken directly from the packet and was never bounded to the RFC maximum of 128. The function computes context->context_len / 8 and then performs memset(context->prefix + context_len, 0, sizeof(context->prefix) - context_len), where context->prefix is a fixed 16-byte array. With context_len between 136 and 255 (and the option length field set to 3, which the pre-fix validation accepts), context_len / 8 evaluates to 17..31, so the memset length 16 - context_len/8 underflows the unsigned size_t argument to roughly SIZE_MAX. This produces an unbounded out-of-bounds memset that zeroes kernel memory well past the 6lo context structure. The defect is reachable from unauthenticated, link-local input: any host on the same link can send a crafted Router Advertisement with a 6CO option. The RA handler validates only the option length field before calling handle_ra_6co(), so a single packet triggers the wild write. The code is compiled when CONFIG_NET_6LO_CONTEXT is enabled. The impact is a reliable remote (adjacent) denial of service via memory corruption, with collateral integrity loss as the memset zeroes contiguous memory before the system faults. Router Advertisements are link-scoped and not forwarded, so the attacker must be on the same link (AV:A). The fix rejects any context_len greater than 128 before the length computation.

The ARM PL011 UART driver in drivers/serial/uart_pl011.c fails to acknowledge receive error interrupts. On the PL011, the framing, parity, break, and overrun error interrupts (PL011_IMSC_ERROR_MASK) are cleared only by writing the interrupt-clear register UARTICR; reading the data register clears the RX interrupt and the per-byte RSR status but not the error interrupt status in MIS. The interrupt service routine pl011_isr() acknowledged only the CTS modem-status interrupt and never wrote icr for the error bits, so an asserted error interrupt remains pending after the ISR returns. When an application enables error-interrupt reporting via the public uart_irq_err_enable() API, an attacker who controls the serial peer can deterministically assert these error bits by injecting line errors on the RX line — a baud/stop-bit mismatch or mid-character break (framing/break error), a flipped parity bit (parity error), or FIFO flooding (overrun error). Because the error interrupt is never cleared, the interrupt line stays asserted and the CPU re-enters pl011_isr() immediately and indefinitely, producing an interrupt-storm livelock from which the core makes no forward progress. The impact is an availability-only denial of service (permanent hang), reachable from an external or removable UART peer. Exploitation is gated by configuration: the error interrupt is off by default and no in-tree subsystem enables it, so only applications that explicitly call uart_irq_err_enable() on a PL011-based, interrupt-driven port are affected. The fix makes pl011_isr() acknowledge the pending error bits via uart->icr, breaking the loop, and additionally clears the latched RSR status in pl011_err_check().

The user-space system-call verifier z_vrfy_z_log_msg_static_create() in subsys/logging/log_msg.c was a pure pass-through: it forwarded the caller-supplied source, desc, package, and data arguments directly to the kernel-mode implementation z_impl_z_log_msg_static_create() without performing any of the mandatory K_SYSCALL_* checks. Because z_log_msg_static_create() is declared __syscall, under CONFIG_USERSPACE any unprivileged user-mode thread can invoke it directly with fully attacker-controlled arguments. The kernel-mode handler dereferences each of these untrusted values: frontend_runtime_filtering() reads through the source pointer as a struct log_source_dynamic_data, cbprintf_package_copy() reads desc.package_len bytes from the package pointer, and z_log_msg_finalize() performs a memcpy() of desc.data_len bytes from the data pointer. With no verification, a user thread can supply arbitrary kernel addresses and arbitrary lengths, and the kernel will read from them. The impact is a kernel-mode denial of service (the kernel faults dereferencing an attacker-chosen pointer) and, where a log backend output is observable to the attacker, disclosure of arbitrary kernel memory copied into the emitted log message — a confidentiality breach across the user/kernel boundary that the userspace sandbox is meant to enforce. The reads do not corrupt kernel memory, so there is no out-of-bounds write primitive. The fix adds the required validation to the verifier: it bounds desc.package_len against Z_LOG_MSG_MAX_PACKAGE, rejects non-NULL/length mismatches, and applies K_SYSCALL_MEMORY_READ() to package, data, and (when runtime filtering with a frontend is enabled) source, so any out-of-bounds or kernel pointer now raises K_OOPS instead of being honored.